| Question |
How can I wire a 653 timer / counter as a counter? |
glx25v |
7 years 5 months ago |
| Question |
What are the different wiring configurations for RTD sensors? |
glx25v |
7 years 5 months ago |
| Question |
What are the color codes for thermocouples? |
glx25v |
7 years 5 months ago |
| Question |
Where can I find additional information covering thermocouples |
glx25v |
7 years 5 months ago |
| Question |
How far can I run my thermocouples? |
glx25v |
7 years 5 months ago |
| Question |
Can I Use Type K thermocouple wires (extension) for an E type thermocouple? What aspects need to be considered for this different type of the thermocouple vs extension wire connection? |
glx25v |
7 years 5 months ago |
| Question |
How can I use a 2 or 4-wire PT100 probe with a West controller designed for 3-wire probes? |
glx25v |
7 years 5 months ago |
| Question |
How is the Modbus comms message formatted for the Controller? |
glx25v |
7 years 5 months ago |
| Question |
How do I use the 2300 with input voltages of greater than 50mV? |
glx25v |
7 years 5 months ago |
| Question |
Why are the valve motor drive (VMD) outputs limited to 120V AC operation? |
glx25v |
7 years 5 months ago |
| Question |
Communication Requirements & Settings for N Series 4100, 6100, 8100 Series Controls. |
glx25v |
7 years 5 months ago |
| Question |
It is impossible to change the Hardware Definition code. |
glx25v |
7 years 5 months ago |
| Question |
Where can I find additional tools for the West 4400 series controllers? |
glx25v |
7 years 5 months ago |
| Question |
How to connect a 3-wire RTD to a 4-wire input? |
glx25v |
7 years 5 months ago |
| Question |
How do I change the thermocouple type or range on my 4400? |
glx25v |
7 years 5 months ago |
| Question |
I can no longer enter one or more of the control modes in my P series control. I have forgotten the unlock codes. How can I gain access to the modes again? |
glx25v |
7 years 5 months ago |
| Question |
How do I change the input range or input type of my 4100+/6100+/8100+? |
glx25v |
7 years 5 months ago |
| Question |
What are the various display strategies available on the 4100/6100/8100+ controls? How do I change the strategy? |
glx25v |
7 years 5 months ago |
| Question |
What are the normal parameters that are accessable to the operator when using the 4100+/6100+/8100+? |
glx25v |
7 years 5 months ago |
| Question |
How do I change the input range of my 6100/8100/4100 (N Series) controller? |
glx25v |
7 years 5 months ago |
| Question |
How do you change from fahrenheit to celsius on my 5010? |
glx25v |
7 years 5 months ago |
| Question |
I want to buy a 6100+, 8100+, or 4100+ control that is the same as one I already have. How do I find out what is in my existing control? |
glx25v |
7 years 5 months ago |
| Question |
How do I change the decimal position in PV and SP in west 6100+ controller? There is a parameter shown in manual for decimal position (dPoS) in configure mode but does not show in display. |
glx25v |
7 years 5 months ago |
| Question |
Changing from thermocouple to RTD input on 2810 or 3810 |
glx25v |
7 years 5 months ago |
| Question |
My P6100 series control does not have the same control response as my older N6100 control. How do I setup the P6100 to control the same as the older control? |
glx25v |
7 years 5 months ago |
