| Question |
How do I scale my 6100, 8100, 4100 plus series control to match my transmitter or other linear signal? |
glx25v |
7 years 3 months ago |
| Question |
What is the default scale when a linear input type such as 4-20mA is selected? |
glx25v |
7 years 3 months ago |
| Question |
Navigation of the various modes of the 6100+/8100+/4100+ control. |
glx25v |
7 years 3 months ago |
| Question |
How do I setup my P Series control for On/Off control? |
glx25v |
7 years 3 months ago |
| Question |
How do I activate/deactivate Self-Tune or Pre-Tune on the 4100+/6100+/8100+? |
glx25v |
7 years 3 months ago |
| Question |
How often do I need to charge my UPS that is currently not being used? |
glx25v |
7 years 3 months ago |
| Question |
My SCR power control has No Output or Full Output at all times with a load connected. How can I test the control? |
glx25v |
7 years 3 months ago |
| Question |
What is the difference between Zero Fired and Phase Angle Fired SCR Power Controls? |
glx25v |
7 years 3 months ago |
| Question |
My 100P series SCR Power control is not working properly. It will not shut off the output fully. |
glx25v |
7 years 3 months ago |
| Question |
How to calculate heat losses and enclosure size for SCR Power Controls |
glx25v |
7 years 3 months ago |
| Question |
How do I control a motor operated variable transformer? |
glx25v |
7 years 3 months ago |
| Question |
What is the setpoint range for a FRC-20 Variac motor control that is configured for limited range? |
glx25v |
7 years 3 months ago |
| Question |
How to add external output modules to MP series control for Variac |
glx25v |
7 years 3 months ago |
| Question |
Calibration of MP Control on a Variac System (Models with Display) |
glx25v |
7 years 3 months ago |
| Question |
How do I calibrate my 4100/6100/8100 (N Series) control? |
glx25v |
7 years 3 months ago |
| Question |
I have a West Plus series control on a plastic machine. The temperature is staying 20 degrees high. Should I try to adjust the PID parameters? Would Auto Tune help? |
glx25v |
7 years 3 months ago |
| Question |
I am having trouble with my control. What informaton is helpful for you to assist with the problem? |
glx25v |
7 years 3 months ago |
| Question |
My controller/indicator sometimes loses its configuration, why is this? |
glx25v |
7 years 3 months ago |
| Question |
How do I specify or request pricing for a new or replacement 'Plus' series control? |
glx25v |
7 years 3 months ago |
| Question |
Why does my display show [HH] instead of the Process Value? |
glx25v |
7 years 3 months ago |
| Question |
What is the difference between the Dual Setpoint and Remote Setpoint options? |
glx25v |
7 years 3 months ago |
| Question |
Why does my display show [LL] instead of the Process Value? |
glx25v |
7 years 3 months ago |
| Question |
Why does my display show [OPEN] instead of the Process Value? |
glx25v |
7 years 3 months ago |
| Question |
How do I enable setpoint ramping on my N Series control? |
glx25v |
7 years 3 months ago |
| Question |
Can I allow my operator to display and change additional parameters while in the operator mode? |
glx25v |
7 years 3 months ago |
