| Question | What is Voltage Squared Linearity in an SCR Power Control | glx25v | 6 hours 15 minutes ago |
| Question | What size VARIAC variable transformer do I need for my hot wire applicaiton? | glx25v | 1 year 4 months ago |
| Question | Typical Capacitor Reforming and Maintenance Recommendations Using an AC Input for Drives which have been Stored for Extended Periods | glx25v | 1 year 5 months ago |
| Question | I have a MP motorized Variac controller. How do I set up the to control the Variac output voltage setpoint with an analog signal? | glx25v | 3 years 2 months ago |
| Basic page | ISE FAQ Home | glx25v | 4 years ago |
| Question | Variacs for my amp! I own an All-Tube (analog power) 100w guitar amp, and have recently been informed of a way to hook up a Variac to the amp. | glx25v | 4 years 5 months ago |
| Question | I have one of your MV or FV systems with automatic regulation. Is there a way to turn off regulation and manually control such a system? | glx25v | 5 years 3 months ago |
| Question | How long do brushes last in VARIAC transformers? How often should they be inspected? | glx25v | 5 years 5 months ago |
| Question | How can I measure DC current with the MMS3000 T6V4? | glx25v | 5 years 7 months ago |
| Question | Sample Rates For DaqPRO Data Loggers | glx25v | 5 years 7 months ago |
| Question | Installation instructions for USB driver. (Required for communications with DaqPro data logger) | glx25v | 5 years 7 months ago |
| Question | My logger cannot connect to an existing DataNet Network | glx25v | 5 years 7 months ago |
| Question | General Setup Requirements / Example for Laurel LT Series Strain Gauge / Load Cell Transmitter or Display | glx25v | 5 years 7 months ago |
| Question | How do I wire my Rustrak 288, 288R and other 200 series recorders? | glx25v | 5 years 7 months ago |
| Question | How can I wire a 653 timer / counter as a counter? | glx25v | 5 years 7 months ago |
| Question | What are the different wiring configurations for RTD sensors? | glx25v | 5 years 7 months ago |
| Question | What are the color codes for thermocouples? | glx25v | 5 years 7 months ago |
| Question | Where can I find additional information covering thermocouples | glx25v | 5 years 7 months ago |
| Question | How far can I run my thermocouples? | glx25v | 5 years 7 months ago |
| Question | Can I Use Type K thermocouple wires (extension) for an E type thermocouple? What aspects need to be considered for this different type of the thermocouple vs extension wire connection? | glx25v | 5 years 7 months ago |
| Question | How can I use a 2 or 4-wire PT100 probe with a West controller designed for 3-wire probes? | glx25v | 5 years 7 months ago |
| Question | How is the Modbus comms message formatted for the Controller? | glx25v | 5 years 7 months ago |
| Question | How do I use the 2300 with input voltages of greater than 50mV? | glx25v | 5 years 7 months ago |
| Question | Why are the valve motor drive (VMD) outputs limited to 120V AC operation? | glx25v | 5 years 7 months ago |
| Question | Communication Requirements & Settings for N Series 4100, 6100, 8100 Series Controls. | glx25v | 5 years 7 months ago |
