| Question |
I have lost my unlock code on my N Series control. How do I find out what it is? |
glx25v |
7 years 3 months ago |
| Question |
How does West Easytune work? |
glx25v |
7 years 3 months ago |
| Question |
Why can't I change parameters such as Proportioning Band, Reset or Rate? |
glx25v |
7 years 3 months ago |
| Question |
How do I configure an analog output to retransmit the displayed temperature? |
glx25v |
7 years 3 months ago |
| Question |
How do I adjust the maximum and minimum setpoint range on my 2800/3800 series controller? |
glx25v |
7 years 3 months ago |
| Question |
When using a control set up for 4-20mA input does the control have protection for input break? |
glx25v |
7 years 3 months ago |
| Question |
I have an ATC 339 Timer that has a long delivery. Is there an alternative that can replace it? |
glx25v |
7 years 3 months ago |
| Question |
I cannot turn on Pre-Tune. What is likely causing this? |
glx25v |
7 years 3 months ago |
| Question |
I cannot activate Self Tune. What is likely causing this? |
glx25v |
7 years 3 months ago |
| Question |
Single Loop Display Is Not Displayed Properly |
glx25v |
7 years 3 months ago |
| Question |
How do I wire a 4 wire RTD to a 3 wire input on a control? |
glx25v |
7 years 3 months ago |
| Question |
What is PID and where can I find additional information? |
glx25v |
7 years 3 months ago |
| Question |
Why am I unable to select the input code that I want in the configuration mode? |
glx25v |
7 years 3 months ago |
| Question |
Is it possible to change between auto/manual control through Modbus communication ? |
glx25v |
7 years 3 months ago |
| Question |
How do I setup wireless communications with the MicroLog data loggers? |
glx25v |
7 years 3 months ago |
| Question |
Communicating with the MLC9000+ versus the original MLC9000 |
glx25v |
7 years 3 months ago |
| Question |
What are some of the improvements that are included with the 4101/6101/8101/8011+? How hard is it to replace my older N series controls or indicators? |
glx25v |
7 years 3 months ago |
| Question |
The transformer dials shown on the site indicate from 0 to 100, yet out put is greater than 100v (140v). How does one know the output voltage when in use if not a Digital model? |
glx25v |
7 years 3 months ago |
| Question |
My Plus controller/indicator has a invalid Unlock code, why is this? |
glx25v |
7 years 3 months ago |
| Question |
How do I calibrate my 4100+/6100+/8100+ (P Series) Control? |
glx25v |
7 years 3 months ago |
| Question |
Where can I download the complete installation and operation manual for the 4100/6100/8100+ and other Plus series controls? |
glx25v |
7 years 3 months ago |
| Question |
What is the output of a thermocouple? |
glx25v |
7 years 3 months ago |
| Question |
MLC nonvolatile memory writing limitations. |
glx25v |
7 years 3 months ago |
| Question |
How do I enable serial communications on my West 5010 controller? |
glx25v |
7 years 3 months ago |
| Question |
How do I reset the Lock Code on my West 5010 controller? |
glx25v |
7 years 3 months ago |
