ISE, Inc. .
|  ISEinc.com  |  Variac.com  |   Literature & Documentation  |

Frequently Asked Questions
 

 
Knowledgebase Home | Glossary | Favorites | Contact Knowledgebase Home | Glossary | Favorites | Contact
Search the Knowledgebase Browse by Category

[Advanced Search]

Advanced Search
* Query:
  Categories:
  Rated:
Search Results for "how to read thermocouple reference table"
There were 47 questions found for your query: (Page 1 of 3)     «« |  Prev | 1 | 2 | 3 | Next | »»
  1. questionWhere can I find additional information covering thermocouples
    ISE Thermocouple Technical Reference

  2. questionWhat is the output of a thermocouple?
    Thermocouple output is a small voltage (mV) that relates to the temperature difference between the sensing end and the termination end. For the voltage relationship: Thermocouple Reference ...

  3. questionI have a very old Variac. Which model can be used to replace this variable transformer?
    The following link will cross reference most models. Variac Cross Reference Most models have the same mounting dimensions.  If your model is not listed please contact ISE for assistance.

  4. questionWhat are the color codes for thermocouples?
    Thermocouple Color Codes: Thermocouple wiring is color coded by thermocouple types. Different countries utilize different color coding. Jacket coloring is sometimes a colored stripe instead o ...

  5. questionHow far can I run my thermocouples?
    Very long thermocouple runs are possible as long as certain precautions are followed. Most instrumentation today have a high input impedance and thermocouple wire is relatively low resistance. ...

  6. questionSample Rates For DaqPRO Data Loggers
    New Page 1 DaqPRO Data Logger Sample Rates Sample rates depend on the number and type of inputs selected. 1 Input - Excluding Temperature: 4000|2000|500|100|50|25|10|1 Sa ...

  7. questionCan I Use Type K thermocouple wires (extension) for an E type thermocouple? What aspects need to be considered for this different type of the thermocouple vs extension wire connection?
     You should always use thermocouple wire or thermocouple extension wire that matches the type of thermocouple that you are using (in your case E).  Thermocouple or thermocouple extensi ...

  8. questionWhat is PID and where can I find additional information?
    ISE PID Technical Reference

  9. questionIs it possible to change between auto/manual control through Modbus communication ?
    To change the controller from auto to manual control (Auto off) using the Modbus communications protocol, the Auto/Manual Control bit needs to be changed. This is done by sending a Modbus messag ...

  10. questionHow do I customize alarm action within Commander when using with Watlow 981-984 Controllers?
    Watlow Series 981-984 Uses Commanders Watlow 982 Modbus Table. Commander does not support the method that Watlow uses for storing the ramp/dwell profile setpoints and therefore does not have t ...

  11. questionThe Microsoft Jet database engine cannot open the file &#39;C:\PROGRAM\FILES\COMMANDER\Live\Commander.mdb. <br>
    After copying backup files from a CD the above error was displayed. 1) In windows explorer find C:PROGRAM FILESCOMMANDERLiveCommander.mdb.2) Right click on the file and select properties3) Un-che ...

  12. questionIt is impossible to change the Hardware Definition code.
    You are likely in the read only mode instead of the configuration mode or the input jumpers are in the wrong position.  Note: changing items in the configuration mode will clear all other se ...

  13. questionHow do I customize alarm action within Commander when used with Watlow 986-989 controllers?
    Watlow Series 986-989 Uses Commanders Watlow 988 Modbus Table. Watlow provides a Low and a High Alarm for each Alarm. The Modbus address 3 contains the status for both alarms. Due t ...

  14. questionHow can I customize alarm action when Commander is used with the Watlow 96 control?
    Watlow Series 96 Watlow provides a Low and a High Alarm for each Alarm. Commander is setup to annunciate both conditions as standard. You can also edit the Commander Modbus Table to annunciat ...

  15. questionHow do I customize alarms within Commander when used with Watlow F4 Controls.
    Watlow Series F4 Watlow provides a Low and a High Alarm for each Alarm. Commander is setup to annunciate both conditions as standard. You can also edit the Commander Modbus Table to annunci ...

  16. questionChanging from thermocouple to RTD input on 2810 or 3810
    You must do the following to switch from thermocouple to RTD on the 2810 / 3810 series:   1) Remove the compensator from terminals 1 & 2 (on housing) 2) Change S1 input switch form thermoc ...

  17. questionOn my West 4400 I have lost my unlock code for entering the setup or the program modes. What can I do to retrieve?
    The factory default setting for the controller's unlock code is 10. This number is entered at the Unlock screen, enabling access to the setup mode parameters. This number can be changed by ...

  18. questionHow do I change the input range or input type of my 4100+/6100+/8100+?
    Changing Input Type and Range on West 6100+, 8100+ & 4100+: Configuration Mode: This mode allows the selection of input type and range and also selects output usage, scaling for linear ...

  19. questionWhy does my display show [OPEN] instead of the Process Value?
    This error message indicates that the signal from your sensor is absent. This may be caused by a faulty sensor, a break in the wiring from the sensor to the instrument, or a loose connection on th ...

  20. questionI have lost my unlock code. How do I find out what it is?
    The factory default setting for the controller's unlock code is 10. This number is entered at the ULOC screen, enabling access to the setup mode parameters. This number can be changed by t ...

(Page 1 of 3)     «« |  Prev | 1 | 2 | 3 | Next | »»

 

Ask ISE a Question

   

Headquarters
10100 Royalton Rd.,  Cleveland, OH  44133  USA
Phone: (440) 237-3200  Fax: (440) 237-1744
Email ISE Cleveland
 
Toledo Area Office
417 Tomahawk Drive,  Maumee, Oh 43537
Phone: 419-893-3330 - FAX: 419-893-2151
Email ISE Toledo  
 

ISE, Inc. Privacy Policy

Click for Cleveland, Ohio Forecast Copyright © 2005 ISE, Inc.  All rights reserved.


Powered by ActiveKB Knowledgebase Software