ISE Knowledge Base - Recent Entries http://isefaq.com/ActiveKB en-us http://isefaq.com/ActiveKB ActiveKB NX sales@iseinc.com Sat, 04 Sep 2010 14:59:51 MST 20 What is the difference between Zero Fired and Phase Angle Fired SCR Power Controls? http://isefaq.com/ActiveKB/questions.php?questionid=136 Phase Angle Fired SCR Power Controls Phase angle SCR power controls adjust the output voltage/wattage by delaying the turn on of the output voltage during each half cycle. The end result is v ... Tue, 10 Aug 2010 14:23:55 MST My P6100 series control does not have the same control response as my older N6100 control. How do I setup the P6100 to control the same as the older control? http://isefaq.com/ActiveKB/questions.php?questionid=135 The difference in control response is likely due to differences between the settings for the Range parameters, PID parameters (Proportioning band, reset and rate) or other parameters in the Se ... Wed, 04 Aug 2010 07:35:23 MST What are some of the improvements that are included with the 4101/6101/8101/8011+? How hard is it to replace my older N series controls or indicators? http://isefaq.com/ActiveKB/questions.php?questionid=60 Plus General Information The easiest to operate control just got easier. The older N series controls and indicators have been replaced with the newer P series controls & indicators. The curre ... Wed, 30 Jun 2010 12:41:29 MST What is the difference between constant current and constant impedance ratings on Variac variable transformers. http://isefaq.com/ActiveKB/questions.php?questionid=134 Constant Current Rating: This is the continuous rated amperage at any output voltage. Constant Impedance Rating: This is the maximum continuous amperage resistive load at 100% voltage output ... Mon, 28 Jun 2010 12:58:01 MST How often do I need to charge my UPS that is currently not being used? http://isefaq.com/ActiveKB/questions.php?questionid=133 A UPS needs to be powered periodically to charge its batteries otherwise battery capacity and run time will be reduced. The below graph shows the typical charging requirements of sealed gelled ... Wed, 16 Jun 2010 12:56:19 MST Why does my Tenor / ATC 650 series timer display show question marks (????) on the display? http://isefaq.com/ActiveKB/questions.php?questionid=132 Check your internal configuration DIP switches. You have chosen a setting that does not exist. The configuration is invalid.Pertains to ATC and Tenor models 655, 651, 652, 653 Fri, 11 Jun 2010 08:56:26 MST My Plus controller/indicator has a invalid Unlock code, why is this? http://isefaq.com/ActiveKB/questions.php?questionid=131 This problem is almost certainly caused by electrical "noise", but it may enter the controller or indicator by a number of routes.It could be line conducted via the mains supply or picked up and t ... Tue, 16 Mar 2010 07:22:44 MST Will the software for my DaqPro work with Windows 7? http://isefaq.com/ActiveKB/questions.php?questionid=130 DaqLab Version 1.4.01 is compatible with Windows 7 Mon, 22 Feb 2010 12:09:13 MST Are there any recommendations for using Using our Variac® variable transformers for light dimming applications? http://isefaq.com/ActiveKB/questions.php?questionid=129 Our Variac® variable transformers are often used for light dimming where electrical noise from common electronic dimmers is a concern. Our variable transformers dim the lights using transformer ... Mon, 22 Feb 2010 09:24:56 MST Can I Use Type K thermocouple wires (extension) for an E type thermocouple? What aspects need to be considered for this different type of the thermocouple vs extension wire connection? http://isefaq.com/ActiveKB/questions.php?questionid=128 You should always use thermocouple wire or thermocouple extension wire that matches the type of thermocouple that you are using (in your case E). Thermocouple or thermocouple extension wire of ... Wed, 10 Feb 2010 08:41:51 MST