.
|  ISEinc.com  |  Variac.com  |   Literature & Documentation  |
Frequently Asked Questions

 

Knowledgebase Home | Glossary | Favorites | Contact Knowledgebase Home | Glossary | Favorites | Contact

Welcome to our knowledge base. To find what you're after, use the search box below or choose a category to view listed questions.

Search the Knowledgebase

Browse by Category

[Advanced Search]

-- Select Category -- Commander Software Controllers     - Watlow Controls     - West (Orig.) 4100/6100/8100 Controls (N Series)     - West (Plus) 4100/6100/8100 (P Series)     - West 2300 Series     - West 2800/3800 Series Controllers     - West 4400 Series Ramp/Dwell Controls     - West 5010 Series     - West MLC Multi-Loop System Data Loggers     - DaqPRO Data Loggers     - MicroLog Data Logger     - MMS3000 Data Logger Pressure Transducers Recorders SCR Power Controls Thermocouples & RTDs Timers & Counters UPS Systems Variacs

Knowledgebase Home > Controllers > West (Plus) 4100/6100/8100 (P Series)

My Plus controller/indicator has a invalid Unlock code, why is this?

Would you like to... Print this page Email this page Post a comment Subscribe me Add to favorites User Opinions How would you rate this answer? Helpful Not helpful Help us improve. Why was this unhelpful? Thank you for rating this answer. This problem is almost certainly caused by electrical "noise", but it may enter the controller or indicator by a number of routes. It could be line conducted via the mains supply or picked up and transmitted via signal input or even an SSR output if one is used. The other method could be airborne radiated noise from nearby equipment such as contactors, spark ignitors motors etc. West controllers and indicators meet the latest CE European Directives regarding EMI susceptibility and EMI emissions (EN61326). If the noise/spikes exceed the levels specified in these Directives, it is possible that the data held in the nonvolatile RAM is being corrupted, causing the controller to return to default values. Relay output control outputs that are connected to an inductive load such as a contactor coil can be a source for this problem. ISE can supply a snubber to help correct. The snubber has an added benefit of increasing the controls internal relay life. The cause of the noise must be identified and suppressed at source. Also, ensure that normal good practice is observed when installing and wiring the controllers. Do not run signal cables near to electrically noisy equipment, use a separate conduit for signal and power cables, use shielded cables (earthed at one point only). The unlock codes must be changed to numbers that are acceptable (0-9999, default is 10 for Setup Mode and 20 for Configuration Mode) using the Configuration software.  The software can be purchased from ISE, P/N PS1-CON.  If controller problem is not resolved using software the unit must be sent in for repair.

Visitor Comments

No visitor comments posted. Post a comment

Related Questions

I have lost my unlock code. How do I find out what it is? On my West 4400 I have lost my unlock code for entering the setup or the program modes. What can I do to retrieve? I can no longer enter one or more of the control modes in my P series control. I have forgotten the unlock codes. How can I gain access to the modes again? How do I change the thermocouple type or range on my 4400? My controller/indicator sometimes loses its configuration, why is this?

Attachments

No attachments were found.

Ask ISE a Question

	Headquarters 10100 Royalton Rd.,  Cleveland, OH  44133  USA Phone: (440) 237-3200  Fax: (440) 237-1744
	Email ISE Cleveland
	Toledo Area Office
	417 Tomahawk Drive,  Maumee, Oh 43537 Phone: 419-893-3330 - FAX: 419-893-2151
	Email ISE Toledo
ISE, Inc. Privacy Policy
	Copyright © 2005 ISE, Inc.  All rights reserved.

Powered by ActiveKB Knowledgebase Software