.
|  ISEinc.com  |  Variac.com  |   Literature & Documentation  |
Frequently Asked Questions

Welcome to our knowledge base. To find what you're after, use the search box below or choose a category to view listed questions.

Search the Knowledgebase

Browse by Category

[Advanced Search]

-- Select Category -- Commander Software Controllers     - Watlow Controls     - West (Orig.) 4100/6100/8100 Controls (N Series)     - West (Plus) 4100/6100/8100 (P Series)     - West 2300 Series     - West 2800/3800 Series Controllers     - West 4400 Series Ramp/Dwell Controls     - West 5010 Series     - West MLC Multi-Loop System Data Loggers     - DaqPRO Data Loggers     - MicroLog Data Logger     - MMS3000 Data Logger Pressure Transducers Recorders SCR Power Controls Thermocouples & RTDs Timers & Counters UPS Systems Variacs

View Questions by Category

There are no sub categories

Thermocouples & RTDs

There were 9 questions found in this category: Can I Use Type K thermocouple wires (extension) for an E type thermocouple? What aspects need to be considered for this different type of the thermocouple vs extension wire connection? You should always use thermocouple wire or thermocouple extension wire that matches the type of thermocouple that you are using (in your case E). Thermocouple or thermocouple extension wire of the proper type must be used all the way from the sensor to measuring instrument. Using a different t ... Do I need to use terminal blocks that are made of the same alloys as the thermocouples? The introduction of an additional alloy such as a terminal or terminal block will not introduce an error as long as the two conductors are at the same temperature. Any errors caused by the additional alloys will cancel out if they are at the same temperature. Since the terminals on terminal bloc ... How do I wire a 4 wire RTD to a 3 wire input on a control? You can connect a 4 wire RTD to a 3 wire instrument. Just use 3 of the wires. Generally a (4) wire RTD will have 2 white wires and 2 red wires. The active element is between a red and a white wire. The remainig wires are for lead wire resistance compensation. Red -------------|VVVVVVVVVVV|-- ... How far can I run my thermocouples? Very long thermocouple runs are possible as long as certain precautions are followed. Most instrumentation today have a high input impedance and thermocouple wire is relatively low resistance. For example: A 1000 ft run of type J 20AWG thermocouple wire has a resistance of 350 ohms. Typical in ... How to connect a 3-wire RTD to a 4-wire input? The compensation leads on a RTD are used to measure and compensate for the lead resistance. (3) Wire RTD (most common) sensing circuits measure the resistance in one leg and assumes the resistance of the other leg is equal. A (4) wire RTD measures the resistance in both legs of the RTD. If the ... What are the color codes for thermocouples? Thermocouple Color Codes: Thermocouple wiring is color coded by thermocouple types. Different countries utilize different color coding. Jacket coloring is sometimes a colored stripe instead of a solid color as shown. United States ASTM: British BS1843: 1952: ... What are the different wiring configurations for RTD sensors? Typical Wiring and Color Code Configurations for 2, 3 & 4 wire RTD's What is the output of a thermocouple? Thermocouple output is a small voltage (mV) that relates to the temperature difference between the sensing end and the termination end. For the voltage relationship: Thermocouple Reference Table (mV vs. Temperature) For additional thermocouple technical data: Thermocouple Technical Refernce Where can I find additional information covering thermocouples ISE Thermocouple Technical Reference

Ask ISE a Question

	Headquarters 10100 Royalton Rd.,  Cleveland, OH  44133  USA Phone: (440) 237-3200  Fax: (440) 237-1744
	Email ISE Cleveland
	Toledo Area Office
	417 Tomahawk Drive,  Maumee, Oh 43537 Phone: 419-893-3330 - FAX: 419-893-2151
	Email ISE Toledo
ISE, Inc. Privacy Policy
	Copyright © 2005 ISE, Inc.  All rights reserved.

Powered by ActiveKB Knowledgebase Software